You can never have too many tips when it comes to painting exterior surfaces. There are clear directions you can follow so that your metal paint job is a successful experience. Whether for wrought iron, aluminum or other metals, there are particular techniques for painting different surfaces. The process of painting metals such as railings, columns, roof vents and decorative pieces like outdoor lamps is similar to painting wood, which means the most important first step is preparation. Most metals are galvanized and need pre-treatment in order for paint to stick to surfaces. Whether you are painting ferrous metal or galvanized metal, the key to a successful job is preparing the surface for the prime coat. Ferrous metal needs a clean rust-free surface. Use a wire brush or a scuff pad to remove rust and wipe the surface with a damp cloth to remove all dust. Areas of sound rust or hard to reach areas can be treated with a solution such as Rust-Oleum™ 3575 Rust Reformer as long as all loose rust has been removed.

Prime the metal immediately after preparation to avoid flash rust from forming on the surface. New galvanized metal needs to be washed with a detergent solution to remove the oily residue inherent to new galvanized metal. If the galvanized is old and has white oxidation on it, this will need to be sanded, wire brushed or otherwise removed. Use 5725 DTM Acrylic Metal Primer/Finish to prime either galvanized or ferrous metal. The 5725 DTM Acrylic Metal Primer is available in 100 White, 120 Red Oxide and 569 Black. You can achieve a satin finish with two coats. For other metals, follow the same preparation guidelines and use 287 Kel-Bond Adhesion Plus Interior/Exterior Primer-Sealer.All Raynor residential steel garage doors are already painted with a baked-on finish. No additional painting is required. If you want to apply another color, however, the following steps are required. NOTE: Only paint the exterior of the door while it is in the closed position. Use the following solution, with a soft bristle brush, to remove mildew and other surface contaminants:

1 cup household Spic n Span® detergent 5 gallons warm water Rinse thoroughly with water. (Do not use a pressure washer to rinse door.) Use a powder cleanser like Comet®, diluted with water, with a soft bristle brush, to prepare the surface for better paint adhesion. Do not use sandpaper, deglossers, or liquid sandpaper to prepare the door surface. Rinse thoroughly with water and allow to dry. Use a high quality acrylic latex exterior paint. Apply according to manufacturer's instructions. Do not use oil-based paint or any "rust-inhibitive" paint. Do not paint in direct sunlight or when surface is warm to the touch. Lap marks will result. Brush application is recommended. Avoid getting paint on any gasket seals between door sections. Not all Raynor doors have these gasket seals. If you are touching up the paint on your door or repainting it, you can match the color precisely with the Raynor Paint Formulas. Just go to your local Sherwin-Williams store with the paint formula to make the match.

IMPORTANT: Since Raynor has no control over re-coating, we do not warrant this product against peeling of the original factory-applied baked-on finish or subsequent coats of paint where re-coating has occurred.christmas tree decorating ideas pink Copyright © 2003-2017 Raynor Garage DoorsAll Rights Reservedwedding chair rentals san diego caHow do you paint a metal door?ready decorated christmas trees To paint a metal door, lay it flat, cover the hardware with masking tape, wipe the door with mineral spirits, sand it, wash it, prime and paint it, unmask the hardware, and hang the door. exterior paint ideas small houses

This six-hour process requires masking tape, mineral spirits, rags, sandpaper, a bucket, water, soap, primer, paint, a paint roller and a paintbrush. How do you refinish cabinets? How do you repaint MDF kitchen cabinets?decorating ideas for study room How do you refinish laminate kitchen cabinets?room decorations for functions Prepare the doorLay the door on a flat surface, and cover the hardware with masking tape. Clean and sand the doorWipe the door with a rag soaked in mineral spirits, and wait for the spirits to dry. Lightly sand the door, and wash it with a solution of water and liquid soap. Rinse with water, and dry the door with a rag.Prime the doorUse a roller to cover the door with primer, and use a paintbrush to neaten the edges and recessed areas. Wait for the primer to dry according to the manufacturer's instructions.

Apply two coats of paintApply a coat of paint with a roller, and smooth the edges with a brush. Cover the front and edges of the door, including those portions that are invisible when the door is closed. Let the paint dry for the amount of time indicated on the can, and then apply a second coat.Unmask and hang the doorRemove the masking tape, and hang the door on its hinges. Learn more about Home Maintenance How do you refinish a cedar chest? To refinish a cedar chest, put it on a tarp, remove the hardware, strip and sand the wood, apply the new stain and sealant, and dry the chest. How do you paint a front door? To paint a front door, remove it, wash and sand it, then apply primer. Paint the door with an angled sash brush and a paint roller. The process takes appro... How do you repair a small hole in drywall? To repair a small hole in drywall, patch the hole with metal drywall patch, a wallboard joint compound, sand the surface, prime and then paint the surface....